320BReal Time Error Codes 现行故障代码
代码 Description Of The Problem 故障描述
1301 Engine oil pressure is too low. 发动机机油压力太低
1302 Engine coolant temperature is too high. 发动机冷却液温度太高
1303 Hydraulic oil temperature is too high. 液压油温度太高
1304 Air filter is clogged. 空滤堵塞
1305 Battery voltage is not normal. 电瓶电压不正常
2201 Governor actuator feedback sensor circuit is open shorted to battery voltage. 油门马达反馈传感器回路形成开路或短路到电瓶正常
2202 Governor actuator feedback sensor circuit is shorted to frame ground.油门马达反馈传感器回路短路到车架接地
2301 Governor actuator feedback signal is not stable. 油门马达反馈信号不稳定
2302 Governor actuator feedback signal deviates.油门马达反馈信号失真
2303 Governor actuator does not move. 油门马达没有移动
2304 Calibration data error. 校正数据错误
3201 Monitor RAM is not normal. 监视器RAM不正常
4101 Electric power supply to the controller is too much (43 volts) ECM的供电太高(43伏)
4102 overcurrent in proportional reducing valve. PRV阀电流过大
4103 Proportional reducing valve circuit is open. PRV阀回路形成开路
4105 overcurrent in digital output (trenching solenoid). 输出电流过大(挖掘电磁阀)
4106 overcurrent in digital output (fine control solenoid). 输出电流过大(精细控制电磁阀)
4107 overcurrent in digital output (travel speed change solenoid).输出电流过大 (行走速度切换电磁阀)
4108 overcurrent in digital output (travel alarm).输出电流过大(行走警报)
410A overcurrent in digital output (swing brake solenoid).输出电流过大(回转制动)
4201 Engine speed is not normal. 发动机速度不正常
4202 Engine coolant temperature sensor is shorted to frame ground.发动机冷却液温度传感器短路到负极(车架上)
4203 Hydraulic oil temperature sensor is shorted to frame ground.液压油温传感器短路到负极
4204 PWM sensor of pump delivery pressure is shorted to frame ground. 泵输送压力传感器短路到负极
4207 PWM sensor of pump delivery pressure is open in circuit.泵输送压力传感器回路形成开路
420A Fuel sensor is shorted to frame ground. 燃油传感器短路到负极
420B Fuel sensor is open or shorted to battery voltage. 燃油传感器形成开路或短路到电瓶正极
420C Electric power supply is too low (below 23 volts). 系统供电电压太低(低于23伏)
420D Electric power supply is too high (above 32 volts).系统供电电压太高(高于32伏)
420E Engine speed dial is not one of the specified 10 setting that are available. 发动机速度拔号盘不在预设定的10个位置之内
4301 Data mismatch 1 between alternator and speed sensor (alternator is abnormal). 交流发电机和速度传感器之间 的数据不匹配(发电机不正常)
4302 Data mismatch 2 between alternator and speed sensor (speed sensor is abnormal).交流发电机和速度传感器之间 的数据不匹配(速度传感器不正常)
4303 Engine stalls. 发动机停机
A201 Monitor communication is not normal. 监视器通讯不正常
A202 Monitor takes too much time to respond to controller's signal.监视器对控制器的信号响应太慢
A203 Communication is abnormal in controller 控制器通讯不正常
图文资料尽在博运油泵配件V1-7-6-2@1@2@7#2#1#4#9纯数字
代码 Description Of The Problem 故障描述
1301 Engine oil pressure is too low. 发动机机油压力太低
1302 Engine coolant temperature is too high. 发动机冷却液温度太高
1303 Hydraulic oil temperature is too high. 液压油温度太高
1304 Air filter is clogged. 空滤堵塞
1305 Battery voltage is not normal. 电瓶电压不正常
2201 Governor actuator feedback sensor circuit is open shorted to battery voltage. 油门马达反馈传感器回路形成开路或短路到电瓶正常
2202 Governor actuator feedback sensor circuit is shorted to frame ground.油门马达反馈传感器回路短路到车架接地
2301 Governor actuator feedback signal is not stable. 油门马达反馈信号不稳定
2302 Governor actuator feedback signal deviates.油门马达反馈信号失真
2303 Governor actuator does not move. 油门马达没有移动
2304 Calibration data error. 校正数据错误
3201 Monitor RAM is not normal. 监视器RAM不正常
4101 Electric power supply to the controller is too much (43 volts) ECM的供电太高(43伏)
4102 overcurrent in proportional reducing valve. PRV阀电流过大
4103 Proportional reducing valve circuit is open. PRV阀回路形成开路
4105 overcurrent in digital output (trenching solenoid). 输出电流过大(挖掘电磁阀)
4106 overcurrent in digital output (fine control solenoid). 输出电流过大(精细控制电磁阀)
4107 overcurrent in digital output (travel speed change solenoid).输出电流过大 (行走速度切换电磁阀)
4108 overcurrent in digital output (travel alarm).输出电流过大(行走警报)
410A overcurrent in digital output (swing brake solenoid).输出电流过大(回转制动)
4201 Engine speed is not normal. 发动机速度不正常
4202 Engine coolant temperature sensor is shorted to frame ground.发动机冷却液温度传感器短路到负极(车架上)
4203 Hydraulic oil temperature sensor is shorted to frame ground.液压油温传感器短路到负极
4204 PWM sensor of pump delivery pressure is shorted to frame ground. 泵输送压力传感器短路到负极
4207 PWM sensor of pump delivery pressure is open in circuit.泵输送压力传感器回路形成开路
420A Fuel sensor is shorted to frame ground. 燃油传感器短路到负极
420B Fuel sensor is open or shorted to battery voltage. 燃油传感器形成开路或短路到电瓶正极
420C Electric power supply is too low (below 23 volts). 系统供电电压太低(低于23伏)
420D Electric power supply is too high (above 32 volts).系统供电电压太高(高于32伏)
420E Engine speed dial is not one of the specified 10 setting that are available. 发动机速度拔号盘不在预设定的10个位置之内
4301 Data mismatch 1 between alternator and speed sensor (alternator is abnormal). 交流发电机和速度传感器之间 的数据不匹配(发电机不正常)
4302 Data mismatch 2 between alternator and speed sensor (speed sensor is abnormal).交流发电机和速度传感器之间 的数据不匹配(速度传感器不正常)
4303 Engine stalls. 发动机停机
A201 Monitor communication is not normal. 监视器通讯不正常
A202 Monitor takes too much time to respond to controller's signal.监视器对控制器的信号响应太慢
A203 Communication is abnormal in controller 控制器通讯不正常
图文资料尽在博运油泵配件V1-7-6-2@1@2@7#2#1#4#9纯数字
